* Optimize all-banks/per-bank refresh timings for Pi5 8GB
* Improve compatibility for booting from some USB SD card readers
https://github.com/raspberrypi/rpi-eeprom/issues/527
* Add enable_rp1_uart=1 to config.txt to initialise RP1 UART0 immediately
prior to starting the ARMs get earlycon on 40-pin header (pins 14,15)
Also requires pciex4_reset=0 in config.txt
earlycon=pl011,0x1f00030000,115200n8
* The [pi5] conditional statement should apply to the entire pi5
family i.e. include cm5 as well.
* Bump SDIO bus priorities to that a GPU/RAM intensive processes
can't unnecessarily stall an I/O processes.
* Assorted log message tidyups.
Interesting changes since the last automatic update:
* Enable network install
* Enable over-clocking frequencies > 3GHz
See: ttps://github.com/raspberrypi/firmware/issues/1876
* Adjust SDRAM refresh rate according to temperature and address a performance
gap between 4GB and 8GB parts in benchmarks.
See: https://github.com/raspberrypi/firmware/issues/1854
* Support custom CA certs with HTTPS boot
* Move non Kernel ARM stages back to 512KB
https://github.com/raspberrypi/firmware/issues/1868
* Assorted HAT+ and NVMe interop improvements.
* Fix TRYBOOT if secure-boot is enabled.
* Preliminary support for D0 and CM5.
* Switch to building the Pi4 firmware from the common Pi4/Pi5
mainline release. This doesn't change the Pi4 features
but should make it quicker to release bug fixes in common code.
* Fix issue that caused the TRYBOOT flag to be lost in secure-boot mode.
* dtoverlay: Use %u when converting u32s to strings
See: https://github.com/raspberrypi/linux/issues/6039
* Improved debug messages for secure-boot.
* Generate the bootloader diagnostics qrcode at run time.
* bootloader: clock_2712: Remove restriction on arm_freq <= 3000
See: https://github.com/raspberrypi/firmware/issues/1876
* arm_dt: Update max_current to match HAT value
* arm_dt: Remove unused legacy parameters (core_freq, arm_freq, uart0_clkrate and cache_line_size)
* Add support for custom CA cert for network install
You need to specify
HTTP_HOST=myhost.com
HTTP_PATH=/path/to/files
HTTP_CACERT_HASH=<hash>
where <hash> is a sha256 hash of the der encoded ca certificate.
CA cert is added using rpi-eeprom-config.
* Optimise Vbat current draw with charging disabled
* Display OTP boot status in UART log messages.
* Preliminary support for secure-boot OTP provisioning.
* Update PCIE DET_WAKE pinmux for D0 products
* Adjust the SDRAM refresh interval based on the temperature. This
addresses the gap in performance between the 8GB and 4GB variants.
See https://github.com/raspberrypi/firmware/issues/1864
* Preliminary support for signed boot.
* Adjust the SDRAM refresh interval based on the temperature. This
addresses the gap in performance between the 8GB and 4GB variants.
See https://github.com/raspberrypi/firmware/issues/1854
* Preliminary support for signed boot
* Fix issues with SFN entries sometimes being treated as LFNs
see https://github.com/raspberrypi/rpi-eeprom/issues/514
* Add a dedicated message for "M.2 HAT" not being found instead of
the generic 'unsupported boot order' message when NVMe boot is
skipped.
* Fix an issue where the boot partition parameter in PM_RSTS was cleared
before being checked.
https://github.com/raspberrypi/firmware/issues/1853
* Add a specific fatal error pattern for RP1 not found - 4 long - 3 short
* Initialise the DWC PHY to enable DWC host+peripheral support under Linux.
Requires 82069a7a02
* Force PWM on 3V3 supply if cameras or HATs are connected or if
power_force_3v3_pwm=1 in config.txt
Resolves an image quality issue with the GS camera.
* Add support for C(arm_min_freq) < 1500 MHz (must be at >= 200 MHz)
* Manufacturing test updates for DVFS.
* Add autodetect support for PCIe expansion HATs
* Add PCIE_PROBE=1 to the EEPROM config for custom PCIe exapansion
designs that do not support the upcoming HAT spec. This gives
similar behaviour to CM4 where PCIe x1 is enumerated to discover NVMe
devices.
* Fix loading of multiple initramfs images that are not 32-bit aligned sizes
https://github.com/raspberrypi/firmware/issues/1843
* Kernel load performance improvement - remove a memcpy
* Fix SDIO / WiFi clock-setup for BOOT_ORDER=0xf14
* Fix SD power-on-reset
* Firmware support for improved watchdog driver
* Update DHCP Option97 to be R,P,i,5 on Pi5
* Add support for HAT gpiomap for improved HAT compatibility.
* Add I2C probe for DSI display auto detect
* Automatically set dtparam=nvme if booted from nvme
* Fix network boot reset issue where only the first attempt works.
* Adding pciex4_reset=0 to config.txt will leave RP1 PCIe enabled when
ARM stage is started.
* Prevent HDMI diagnostics being displayed immediately when waking
after HALT.
* Update board-name - "Rasberry Pi 5"
