image: 2712: Update config for POWER_OFF_ON_HALT and NET_INSTALL_AT_POWER_ON

* The 2024-11-12 automatically sets the POWER_OFF_ON_HALT property
  according to the board-type so remove the override network install
  images.
* Set NET_INSTALL_AT_POWER_ON=1 by default which briefly display
  the network-install / boot-menu UI after a cold power-on.
  This can be switched off by removing the line
  either via "rpi-eeprom-config --edit" or the new menu in raspi-config
  Advanced Options.

firmware-2711/old/critical/pieeprom-2020-04-16.bin

@@ -1 +0,0 @@
-../beta/pieeprom-2020-04-16.bin

firmware-2711/old/critical/vl805-000137ad.bin

@@ -1 +0,0 @@
-../beta/vl805-000137ad.bin

firmware-2711/old/stable/pieeprom-2020-04-16.bin

@@ -1 +0,0 @@
-../beta/pieeprom-2020-04-16.bin

firmware-2711/old/stable/vl805-000137ad.bin

@@ -1 +0,0 @@
-../beta/vl805-000137ad.bin

firmware-2711/release-notes.md

@@ -1,5 +1,41 @@
 # Raspberry Pi4 bootloader EEPROM release notes
 
+## 2024-10-21: Fix PCIe BAR issue for some switches  (latest)
+
+* Boot-menu improvements
+  Remain in the forced boot mode until the menu is used to select a different
+  boot-mode or reset to the original boot-order.
+
+## 2024-10-10: Use soft-reset to preseve SDRAM contents after ramoops (latest)
+
+* SD card high-speed/low-voltage mode can only be exited by powercycling.
+  Pi 4s before rev 1.4 lack the power switch required to do this, so must
+  resort to a global reset that turns off many things, including SDRAM.
+
+  To ensure correct operation, the bootloader checks that the SD I/O
+  voltage is the expected 3.3V, forcing a power cycle if it isn't.
+  However, this doesn't take advantage of presence of the dedicated SD
+  power switch, always forcing a global reset, a consequence of which can
+  be the loss of SDRAM content - including any ramoops dump of the crash
+  logs.
+
+  Make the bootloader more SD_PWR_ON aware, only triggering a global reset
+  if one isn't found.
+  See: https://github.com/raspberrypi/linux/issues/5298
+* Remove requirement for GPT ptable array  to be at LBA-2
+  See: https://github.com/raspberrypi/rpi-eeprom/issues/585
+* Introduce a new boot-menu feature where pressing SPACE at power on
+  gives the user a one-shot option to select a different boot mode.
+  e.g. Select USB boot if the default SD card is corrupted or unavailable.
+* Display the bootloader network-install UI for longer on a cold boot to make
+  this feature more visible to first time users.
+  To revert to the previous behaviour remove NET_INSTALL_AT_POWER_ON=1
+  from the bootloader config.
+* Default to 2GB start for PCI bus addresses on 2711 and 2712
+  This change also constrains the window size to 2GB, so all PCI bus address
+  assignments fall below 4GB, avoiding a potential bug with 32-bit BARs in
+  esoteric bus topologies (e.g. lots of GPUs).
+
 ## 2024-09-05: Fix self-update if EEPROM is write-protected (latest)
 * arm_dt: Consult the hat_map for all HATs
 * USB boot - ignore RP2 / RP3 MSD device in BOOTSEL mode.
@@ -11,7 +47,7 @@
 ## 2024-08-14 (recovery.bin) -  Add support for OTP metadata (latest)
 * Update to recovery.bin to output metadata about OTP during rpiboot
 
-## 2024-07-30 - USB boot fixes for CM4-S and interop improvments (latest)
+## 2024-07-30 - USB boot fixes for CM4-S and interop improvements (latest)
   * Resolve USB boot regression in 2024-04-17 relase on CM4S
     See https://github.com/raspberrypi/rpi-eeprom/issues/588
   * Improve compatibility for booting from some USB SD card readers